Technical Foundation
What Is a Cork Roll Stock?
Cork roll stock is sheet material made from granulated natural cork bark, either compressed and bonded on its own (pure cork) or blended with a synthetic rubber binder — most commonly nitrile (NBR) or neoprene (CR) — to improve oil resistance, compression set, and sealing performance. Pure cork offers excellent compressibility and vibration damping at low cost but limited resistance to oils and solvents; cork-rubber blends trade some compressibility for chemical resistance and a longer service life under repeated compression, which is why most industrial gasket applications specify a blend rather than pure cork.
Roll stock is sold by thickness and blend ratio (the percentage of rubber binder, commonly 30-70% by weight) rather than by a single material grade, and thickness tolerance matters for gasket applications where the material must compress into a consistent seal under bolt torque. Cork composition is also used un-bonded to gaskets, as vibration-isolation pads under machinery and as an acoustic underlayment beneath flooring, where its cellular structure absorbs impact and sound transmission.
Prefer a quick quote?
Get Cork Roll Stock Pricing in Your Inbox
Skip the search — tell us the thickness, cork/rubber blend and roll width and we will come back with pricing.
| Spec | What It Means | Why It Matters |
|---|---|---|
| Composition | Pure cork vs. cork-nitrile or cork-neoprene blend | Blends resist oil/fuel exposure and hold compression set better than pure cork |
| Thickness | 1/32 in to 1 in, with tolerance typically ±10% | Determines gasket compressibility and the bolt-load range needed for a proper seal |
| Density | Measured in lb/ft³, affects compressibility and recovery | Lower density compresses more easily; higher density resists extrusion under high bolt load |
| Temperature Rating | Typically -50°F to 250°F depending on binder | Sets the upper service temperature before binder degradation and seal failure |
| Adhesive Backing | Plain, or pressure-sensitive adhesive on one/both faces | Adhesive-backed rolls speed installation for damping pads without separate fastening |
Shop Cork Roll Stock
Browse Cork Roll Stock Sub-Categories
Organised by cork composition. Pick a sub-category, or describe the sealing, damping or cushioning job and let ChatMRO match the material.
How it works
From Half-Remembered Part Number to PO, in Three Steps.
Ask
Type an MPN, paste a spec sheet, or describe the part in plain English. ChatMRO understands engineer-speak.
Compare
Side-by-side specs, cross-references, and equivalents from multiple sources — without the clutter of endless browser tabs.
Quote & Buy
Request a quote or add to cart. Volume discounts, VAT-aware pricing, and consolidated procurement — all in one place.
Applications
Where Cork Roll Stock Get Used
Cork roll stock is specified anywhere low-pressure sealing, vibration damping, or acoustic cushioning is needed at low cost.
Gasket Fabrication
Die-cut or hand-cut into custom gaskets for engine covers, pump housings, and access panels.
Machinery Vibration Isolation
Cork pads placed under compressors, pumps, and HVAC equipment to dampen structural vibration transmission.
Acoustic Flooring Underlayment
Cork roll laid beneath flooring in commercial and residential construction to reduce impact sound transmission.
Automotive & Small Engine Repair
Cork-nitrile gaskets cut for valve covers, oil pans, and fuel system components exposed to petroleum products.
Electrical Enclosure Sealing
Pure cork strip gaskets sealing low-pressure electrical panel and junction box covers.
Packaging & Cushioning
Cork sheet used as a resilient cushioning layer for shipping fragile or vibration-sensitive equipment.
FAQ
Cork Roll Stock Questions, Answered
Should I choose pure cork or a cork-rubber blend?
Pure cork is lower cost and highly compressible, suited to low-pressure, non-oil-exposed sealing and cushioning. A cork-nitrile blend adds resistance to oils, fuels, and solvents and holds compression set better under repeated bolt-torque cycling, making it the standard choice for engine, pump, and hydraulic equipment gaskets. Cork-neoprene blends offer better weathering and ozone resistance for outdoor or UV-exposed applications.
How do I choose the right thickness for a gasket?
Thickness should be the minimum that reliably fills the surface irregularities of the mating flanges — thicker material compresses more but requires more bolt load to seal fully and is more prone to creep over time. As a general rule, 1/16 in to 1/8 in covers most machinery gasket applications; thinner stock suits precision-machined flat surfaces.
What's the maximum temperature cork-rubber gasket material can handle?
Cork-nitrile blends typically rate to around 250°F (121°C) continuous service; cork-neoprene blends are similar or slightly lower. Beyond that range the rubber binder degrades, losing compression set resistance and sealing ability — check the specific product's technical datasheet, as ratings vary by binder ratio and manufacturer.
Can cork roll stock be die-cut for custom gasket shapes?
Yes — cork and cork-rubber sheet is one of the more common materials for die-cutting or hand-cutting custom gaskets, since it's soft enough to cut cleanly with a steel-rule die, gasket punch, or utility knife without cracking, unlike harder rubber or metal gasket materials.
Is adhesive-backed cork roll suitable for vibration isolation pads?
Yes — pressure-sensitive adhesive backing on one or both faces lets installers position cork damping pads under equipment feet or between panels without separate fasteners, which speeds installation for retrofits where drilling isn't practical. For heavier machinery, adhesive alone may not provide enough shear resistance and mechanical fastening should be added.
Keep browsing
Related Categories
Explore More
Find Your Next Part Now.
Describe a part number, spec or what it does.