Technical Foundation
What Is a Conduit and Outlet Bodie?
Conduit outlet bodies are cast fittings inserted into a rigid, IMC, or EMT conduit run to provide a pull point for wire, a change of direction, or a junction for splicing, without requiring a full junction box. The letter designation — LB, LL, LR, T, C — describes the internal geometry: an LB enters and exits at 90 degrees with the access opening on the back, an LL or LR offsets the exit to the left or right, and a T body provides a straight run with a perpendicular branch.
Bodies are matched to conduit trade size and material (aluminum, malleable iron, or PVC) and always installed with a gasketed cover to maintain the conduit system's environmental rating — NEMA 3R, 4, or 4X depending on the application. Fill capacity is limited by code: outlet bodies are sized for pulling and splicing, not as a substitute for a junction box when high conductor fill is required.
Prefer a quick quote?
Get Conduit and Outlet Bodies Pricing in Your Inbox
Skip the search — tell us the conduit size, body configuration (LB/LL/LR/T/C) and material and we will come back with pricing.
| Spec | What It Means | Why It Matters |
|---|---|---|
| Body Type | LB, LL, LR, T, C, LBD configurations | Geometry determines which entry/exit and access orientation fits the physical routing |
| Trade Size | 1/2in through 4in typical range | Must match the conduit trade size exactly for a threaded, sealed connection |
| Material | Aluminum, malleable iron, PVC | Determines corrosion resistance, weight and compatibility with the conduit material used |
| Hub Type | Threaded, set-screw, compression | Must match the conduit termination method used elsewhere in the run |
| Cover & Gasket Rating | NEMA 3R, 4, 4X depending on gasket/cover | Determines the outdoor/washdown environmental rating of the sealed body assembly |
Shop Conduit and Outlet Bodies
Browse Conduit and Outlet Bodies Sub-Categories
Organised by body configuration. Pick a sub-category, or describe your conduit run and let ChatMRO match the right outlet body.
How it works
From Half-Remembered Part Number to PO, in Three Steps.
Ask
Type an MPN, paste a spec sheet, or describe the part in plain English. ChatMRO understands engineer-speak.
Compare
Side-by-side specs, cross-references, and equivalents from multiple sources — without the clutter of endless browser tabs.
Quote & Buy
Request a quote or add to cart. Volume discounts, VAT-aware pricing, and consolidated procurement — all in one place.
Applications
Where Conduit and Outlet Bodies Get Used
Outlet bodies are used anywhere a conduit run needs a pull point, direction change or splice access without installing a full junction box.
Industrial Electrical Distribution
LB and T-type bodies used as pull points along rigid conduit runs in plant and process electrical systems.
Outdoor & Exposed Conduit Runs
NEMA 3R/4-rated outlet bodies with gasketed covers protecting wire pulls on exterior conduit installations.
Hazardous Location Wiring
Explosion-proof rated outlet bodies used in Class I/II hazardous areas per NEC Article 501/502 requirements.
Commercial Building Electrical
Conduit bodies used at direction changes and splice points in exposed EMT and rigid conduit runs.
Water & Wastewater Treatment Facilities
Corrosion-resistant PVC and coated aluminum bodies specified for washdown and chemically exposed environments.
FAQ
Conduit and Outlet Bodies Questions, Answered
What's the difference between an LB, LL and LR conduit body?
All three change conduit direction by 90 degrees, differing in which side the access opening and offset fall on: an LB has the cover on the back (opposite the run), while LL and LR offset the exit conduit to the left or right respectively as viewed from the access opening. The choice depends on the physical routing and access clearance at the installation point.
Can I use a conduit outlet body instead of a junction box?
Outlet bodies can serve as a pull point or splice location within code fill limits, but they have significantly less internal volume than a standard junction box — the NEC limits how many conductors and splices can be housed based on the body's volume, so high conductor-count splices typically still require a junction box.
Do outlet bodies need a specific cover and gasket?
Yes — the cover and gasket combination determines the assembly's environmental rating (NEMA 3R for rain-tight, NEMA 4/4X for washdown/corrosion resistance), so the cover and gasket must be selected to match the required rating for the installation location, not just any cover that physically fits.
What material should I use — aluminum, malleable iron, or PVC?
Aluminum is common for general indoor/outdoor use due to its light weight and corrosion resistance; malleable iron offers greater mechanical durability for high-impact or hazardous locations; PVC is used for corrosion-prone or underground/wet environments like water treatment facilities. Match material to both the conduit type in use and the environmental exposure.
Are explosion-proof outlet bodies different from standard ones?
Yes — explosion-proof (hazardous location) rated outlet bodies are designed and listed to contain an internal arc or explosion per NEC Article 501/502, with specific threaded joint tolerances and cover fastening requirements that standard outlet bodies don't meet, so they cannot be substituted in classified hazardous areas.
Keep browsing
Related Categories
Explore More
- Yoke Ends
- Earth Ground Resistance Tester Accessories
- Cable and Wire Crimping Tools
- Gas Infrared Tube Heaters
- Air Powered Airless Paint Sprayers
- Electronic Motor Starters
- Electrical Wall Plates
- Air Cleaner Accessories
- Hydraulic Two Stage Gear Pumps
- Electric Screwdrivers
- Hydraulic Reservoir Tanks
- Colony Counters
Find Your Next Part Now.
Describe a part number, spec or what it does.